Laser Settings Explained: Joules, Milliseconds and Spot Size

A simple guide to the three settings behind every safe laser hair removal treatment

Short answer: Every laser shot is controlled by three settings. Fluence (joules per square centimetre, J/cm²) is how strong the shot is. Pulse duration (milliseconds, ms) is how quickly that energy goes in. Spot size (millimetres, mm) is how wide the beam is, which also decides how deep it reaches. Safe laser hair removal is about balancing all three so the hair follicle heats up while the skin stays cool.

The three settings at a glance

Setting Unit Think of it as Turn it up Turn it down
Fluence ("joules") J/cm² How strong the shot is More heat in the follicle, but more risk of burns and pain Safer and more comfortable, but too low and hair grows back
Pulse duration ms How fast the heat goes in Longer = gentler, kinder to darker skin, suits coarse hair Shorter = a quick, intense burst for fine hair, harsher on skin
Spot size mm How wide and deep the beam is Bigger = deeper reach and faster coverage Smaller = shallower and more precise

The golden rule we teach every student: heat the hair, not the skin.

Joules (fluence): how strong is the shot?

A joule is a unit of energy. Fluence is that energy spread over the area of the laser spot, so it is measured in joules per square centimetre (J/cm²). When therapists talk about "turning the joules up", they almost always mean fluence.

Too high, and you risk burns, blisters, pigmentation changes and a lot of pain. Too low, and the follicle survives, the hair grows back, and in some cases fine hair can even be stimulated to grow (paradoxical hypertrichosis).

You generally go lower for darker or tanned skin (the skin's own melanin absorbs energy), for thick, dark, dense hair (it heats up fast) and on a client's first session. You can go higher on fair skin, finer hair and once the skin has tolerated earlier sessions.

The correct end point is slight redness and small raised bumps around each follicle (perifollicular oedema) within a few minutes. Greying or whitening skin, blistering or a burning sensation mean the fluence is too high.

Milliseconds (pulse duration): how fast does the heat go in?

Pulse duration is how long each flash lasts. One millisecond is a thousandth of a second. The same energy can go in as a sharp burst or a slow, gentle push.

The idea behind it is thermal relaxation time (TRT): how long something takes to lose about half its heat. Thin things cool fast; thick things hold heat. The skin's top layer cools in a few milliseconds (roughly 3 to 10 ms), while a hair follicle holds heat much longer (roughly 10 to 100 ms, depending on hair thickness).

So we choose a pulse that is longer than the skin's TRT but no longer than the hair's. The skin has time to cool during the pulse; the follicle keeps building heat until it is destroyed.

Think of a hot cup of tea and a thin teaspoon. The spoon cools in seconds while the tea stays hot. The skin is the spoon; the follicle is the tea.

Easy way to remember it: fine hair, fast pulse. Thick hair or darker skin, long pulse.

Spot size: why bigger or smaller?

Spot size is the width of the beam on the skin, in millimetres. Light scatters sideways as it enters the skin. With a small spot, much of the light scatters out of the edges and fades before it gets deep. With a large spot, the centre of the beam stays focused and more energy reaches the hair bulb.

Pick a bigger spot for large areas such as legs, back, chest and arms: it reaches deeper follicles, covers the area faster and can often work at a slightly lower fluence.

Pick a smaller spot for small or curved areas such as the upper lip, chin, sideburns, hairline, fingers and toes, and for neat edges around a shaped bikini line or moles you are avoiding. Smaller spots also allow a higher fluence where it is needed.

Whatever the size, overlap each shot by about 10 to 20% so you don't leave stripes of untreated hair, and never stack shots in the same place.

How the settings work together

At the same fluence, a bigger spot delivers more total energy in every shot. For example, at 10 J/cm²:

12 mm spot 18 mm spot
Area of the spot about 1.1 cm² about 2.5 cm²
Total energy per shot about 11 J about 25 J

That is more than double the energy, which is why a larger spot reaches deeper, and why you may need to reduce the fluence slightly when you move up a size. If a client finds a setting too hot, lengthening the pulse spreads the heat out before you need to drop the fluence.

Learn this hands-on

Every laser and skin type is different, so settings always start from the manufacturer's guidelines, a thorough consultation and a patch test. On our CPD Laser Hair Removal course you study the theory online, then spend a full practical day treating real models on the Cynosure Elite in our working clinic in East Grinstead.

Related: Fitzpatrick skin types explained · Do you need a qualification to do laser hair removal?


About Enhance Training Academy

Enhance Training Academy is the training arm of Enhance Aesthetics & Beauty, a working laser, beauty and aesthetics clinic at 1 Whitehall Parade, London Road, East Grinstead, RH19 1AP. Our tutors are practising therapists who treat clients every day. We offer CPD accredited courses and VTCT qualifications, with online theory and hands-on practical training. Call 01342 301544 or email [email protected].

← Back to all blog posts